Home

How to flush a water heater: tank and tankless steps

By Roof & Router Team. Updated October 19, 2026.

Short answer: To flush a tank water heater, shut off the breaker or set the gas control to OFF, let it cool, close the cold supply, run a hose from the drain valve to a drain, open a hot faucet, and flush with cold water until it runs clear. A.O. Smith and Rheem say to flush about once a year, and Rheem says every six months with hard water. Tankless units are descaled instead, at least yearly per Rinnai and Navien.

Skip to what to buy (5 types) ↓

How do you flush a water heater?

Flushing means draining the tank through its drain valve and running cold water through it until the sediment stops coming out. Here are the steps from A.O. Smith’s flushing guide, with notes from Rheem. Always check your own model’s manual first.

What you need: a garden hose, a flathead screwdriver (some drain valves need one), thick gloves and safety goggles, a bucket and towels.

  1. Turn off the heat source. On an electric heater, switch off its breaker or disconnect. On a gas heater, set the thermostat dial to OFF and turn off the gas valve, as A.O. Smith directs.
  2. Let the water cool. A.O. Smith says to wait a few hours before draining. Hot tank water can scald (see the chart below).
  3. Close the cold water supply valve on the supply pipe, or the main shutoff.
  4. Connect a garden hose to the drain valve near the bottom of the tank. Run the other end to a floor drain, outdoors, or a bucket.
  5. Open a hot water faucet inside the house so air can enter and the tank drains smoothly. Rheem’s version opens the pressure relief valve first.
  6. Open the drain valve by hand or with a screwdriver. A.O. Smith says most tanks take 20 to 40 minutes to drain, and heavy sediment can extend that.
  7. Flush. With the drain still open, turn the cold supply back on to push out the remaining sediment. A.O. Smith says to keep flushing with cold water until no sediment comes out.
  8. Close the drain valve once the water runs clear, then remove the hose.
  9. Refill. Close the relief valve if you opened it. Turn the cold supply fully on and leave a hot faucet open. Rheem says to close the faucets only once water flows from them, which shows the tank is full.
  10. Restore heat. Turn the breaker back on, or turn the gas back on and relight the pilot following the manufacturer’s instructions. A.O. Smith also says to run a hot tap for about 3 minutes to clear trapped air.

If the drain valve won’t open or keeps clogging, A.O. Smith says to call a plumber. Rheem also warns that hardened sediment in older tanks can cause leaks or damage if you flush it yourself, and it suggests a professional for heaters 8 to 12 years old or older.

How often should you flush a water heater?

Most manufacturers say once a year, more often with hard water. Hard water carries more dissolved minerals, which settle as sediment in a tank or form scale in a tankless unit.

Source Tank water heater Tankless water heater
U.S. DOE Energy Saver Drain a quart every 3 months Not covered
A.O. Smith At least once a year; service twice a year with hard water Descale periodically per the manual; service twice a year with hard water
Rheem Once a year; about every 6 months with hard water About once a year; about every 6 months with hard water
Bradford White Yearly professional maintenance, including draining Not covered
Rinnai Not applicable At least once a year
Navien Not applicable At least once a year; more often with hard water

DOE’s quarterly quart is a mini-drain, not a full flush. It says the sediment it removes “impedes heat transfer and lowers the efficiency of your heater,” and to follow the manufacturer’s directions.

Safety: gas vs. electric water heaters

How fast hot water burns, from the State residential gas water heater manual:

Water temperature Time to a first-degree burn Time to a permanent (2nd or 3rd degree) burn
116°F 35 minutes 45 minutes
122°F 1 minute 5 minutes
131°F 5 seconds 25 seconds
140°F 2 seconds 5 seconds
149°F 1 second 2 seconds

That is why waiting a few hours matters. A tank set to 140°F can cause a permanent burn in 5 seconds. For setting the thermostat after you refill, see our water heater temperature guide.

What happens if you don’t flush your water heater?

Minerals in the water settle on the bottom of the tank as sediment. Manufacturers list these effects:

Why is my water heater making popping or rumbling noises?

Sediment is the usual cause. A.O. Smith explains that sediment on the tank bottom traps steam bubbles that “have to fight to escape,” then pop when they break free. The State manual says sediment can cause “rumbling” or “percolating” sounds, and Bradford White lists popping, rumbling and banging as warning signs.

A.O. Smith calls flushing “the best cure for a popping water heater.” Crackling can also come from a reaction at the anode rod, A.O. Smith notes.

How do you flush a tankless water heater?

Tankless units don’t hold a tank of water, so they are descaled instead. A pump circulates a descaling solution through the heat exchanger to dissolve mineral scale. A.O. Smith’s steps, with Rinnai and Navien details:

  1. Turn off power and gas to the unit, as Rinnai and A.O. Smith direct.
  2. Close the isolation valves. These are the hot (red) and cold (blue) shutoff valves under the unit with small service ports. Rinnai also closes the main valve feeding the home.
  3. Relieve pressure. Rinnai says to remove the purge port valve caps slowly.
  4. Connect hoses. One hose runs from the pump to the cold-side service port; the other runs from the hot-side port back into the bucket. Navien lists a double-ended washing machine hose, a submersible pump and a 5-gallon bucket.
  5. Add solution. Rinnai calls for 4 gallons of undiluted white vinegar and says “never use chemical solutions of any kind.” Navien allows white vinegar or an approved descaling solution.
  6. Circulate for about 45 minutes. Navien says at least 45 minutes; A.O. Smith calls about 45 minutes typical but says to follow your kit.
  7. Rinse with fresh water. A.O. Smith says at least 5 minutes; Navien says at least 10.
  8. Clean the inlet filter. A.O. Smith includes this step, and Navien says to rinse the cold-water inlet screen and scrub it with a brush if needed.
  9. Close the service ports, replace the caps, and reopen the valves. Run a hot tap until the air clears, which Rinnai says may take 2 to 3 minutes.

Some models have a service mode or bypass valve, so follow your manual. Navien says skipping maintenance in the manual may affect the warranty. If you’re still choosing a heater, our tankless vs. tank water heater guide compares upkeep and cost.

Check the anode rod and T&P valve while you’re there

An anode rod is a metal rod inside the tank that corrodes so the tank doesn’t. The T&P valve is the safety valve on the top or side of the tank that releases water if pressure or temperature get too high.

Task How often What to look for
Inspect the anode rod Once a year (A.O. Smith, Rheem); professional exam every 5 years (A.O. Smith) A healthy rod is about half an inch thick. Replace it when about 6 inches of core wire is exposed (A.O. Smith).
Test the T&P valve At least once a year (State manual, A.O. Smith); every 5 years by a pro (A.O. Smith) Lift the lever a few times. Water should discharge from the tank (A.O. Smith).
Professional check-up Once a year (State manual, Bradford White) Venting system, main burner and pilot (State manual)

T&P test: Put a bucket under the discharge pipe and lift the lever a few times, as A.O. Smith describes, and be careful: A.O. Smith warns the water can be very hot. If nothing comes out, A.O. Smith says to drain the tank and replace the valve. Rheem says to replace one that keeps leaking afterward, and calls that a job for a plumber. A.O. Smith says the valve opens at 150 psi and fully at 210°F.

Anode tips: A rotten egg smell can come from bacteria reacting with a magnesium anode; Rheem suggests an aluminum or powered anode. The State manual warns not to remove the anode and leave the tank without one, which voids the tank warranty.

When to flush as part of seasonal upkeep

Fall is a convenient time, since you’re already checking other systems. Add it to our winterize your house checklist. If the flush shows a leaking tank or your heater is near the end of its life (see how long a water heater lasts), check what size water heater you need before you shop.

What to buy

The main types, who each one suits, and what to check before you buy. Each link opens matching products at that store.

  1. Garden hose

    Best for: running drain water from the tank's drain valve to a floor drain or outside.

    Look for: enough length to reach a drain lower than the valve, and a tight-sealing coupling.

  2. Water heater drain valve (brass, full-port)

    Best for: replacing a drain valve that is clogged or won't close tightly.

    Look for: a thread size that matches your tank's drain fitting.

  3. Hose thread drain cap

    Best for: sealing a drain valve that drips after you close it.

    Look for: standard garden hose threads and a rubber washer inside.

  4. Tankless water heater flush kit

    Best for: descaling a tankless unit through its isolation valves.

    Look for: a submersible pump, two hoses that fit your service ports, and a bucket of about 5 gallons.

  5. Tankless descaling solution

    Best for: removing mineral scale from a tankless heat exchanger.

    Look for: a product your heater's manufacturer approves; check the manual before using any chemical.

These links open search results at Amazon, Walmart, The Home Depot, Lowe's and Best Buy. We do not earn anything from them, and no brand paid to be listed.

Quick answers

How often should you flush a water heater?
About once a year for most tank water heaters, according to A.O. Smith and Rheem. Both say to flush more often with hard water, about every six months per Rheem.
What happens if you don't flush your water heater?
Sediment builds up on the bottom of the tank. Rheem and A.O. Smith say that can lower efficiency, raise energy bills, cause noise, clog water lines and shorten the heater's life.
Why is my water heater making a popping noise?
Usually sediment. A.O. Smith says sediment on the tank bottom traps steam bubbles that pop as they escape, and it calls flushing the best cure.
How long does it take to flush a water heater?
A.O. Smith says draining a tank takes about 20 to 40 minutes, longer with heavy sediment. Add a few hours beforehand to let the water cool and time to flush and refill.
How do you flush a tankless water heater?
Close the hot and cold isolation valves, connect a pump and hoses to the service ports, and circulate descaling solution or white vinegar for about 45 minutes, then rinse with fresh water. Rinnai calls for 4 gallons of undiluted white vinegar; follow your own unit's manual.
How often should you check the anode rod in a water heater?
A.O. Smith and Rheem recommend inspecting it once a year. A.O. Smith says to replace it when about 6 inches of core wire is exposed.
Can I flush a water heater with vinegar?
For tankless units, Rinnai and Navien list white vinegar as a descaling option. The tank-flushing steps from A.O. Smith and Rheem use plain cold water.

Sources